Operation Guide Vaporesso Revenger Kit Manual Operations Guide

Vaporesso Revenger Kit

utilizes the most advanced chipset OMNI Board 2.0 with a range of 5 to 220W, multiple output modes with quick charge system and Remaining Charging Time, driven by two 18650 batteries (sold separately). As the 1st in vaping history, It features the In-Mould Labeling (IML) case for greater wear resistance, graphic quality and fine texture. It is equipped with NRG Tank, a masterpiece of everyday vape and cloud chasing, featuring innovative GT Cores that comes in traditional and signature CCELL Ceramic Coil. The Slide-n-Fill design makes refill easier than ever. The heating insulation layer on the bottom demonstrates how Vaporesso care for safer and relaxing vaping experience. Furthermore, the mesh drip tip with specially engineered structure will prevent any spit back. The ergonomic design integrates the all metal fire button on the side for better grip and the industry leading OLED screen with the mode buttons on the side. You would get all the information on your vape on this OLED screen, including useful tips like the remaining time to get your battery fully charged, backed by OMNI Board 2.0. Enjoy the flavor and vapor out of the variety of GT cores available.

How to Use

1. Switch On/Off:

Press the fire button 5 times in quick succession within 2 seconds to turn the device on. In the same way, the device will be powered off after 5 presses.

2. Vaping:

Hold the fire button and inhale through the mouthpiece. Release the fire button and exhale.

3. Screen Display:

After switch on, the OLED displays voltage resistance, battery level, temperature, output wattage etc. The display will change to Real Time Clock after 10 seconds if unused and the Real Time Clock will be shut off after 15 minutes if unused. Press “+” or “-“ or Mode button once and the screen will be lit with Real Time Clock display and press “+” or “-“ or Mode button again, the screen will be lit with main manual. Press the fire button at any time, the screen will be lit with main manual.

4. Automatic atomizer recognition:

The mod will read the coil’s resistance as soon as the connection is detected. It will also recognize coil type, when a kanthal coil is used, the mod will shift from TC to wattage mode automatically.

5. Adjustment buttons lock/unlock:

Keep pressing mode button and “+”button simultaneously for two seconds when the device is powered on, then the up and down buttons will be locked and the screen will display “SYSTEM LOCKED”. In the same way, pressing the up and mode buttons can be unlocked and the screen will display “SYSTEM UNLOCKED”.

6. Switch display mode:

Keep pressing up button and down button simultaneously for two seconds, the screen display will rotate 180degrees.

7. Switch vaping modes:

Long press the mode button for three seconds to switch among VW (H/N/S) /VT(Ni200, SS, Ti)/ TCR / BYPASS / CCW / CCT modes.

8. Charging:

It is with Quick Charge System and equalizing charge system. Simply plug in the USB cable to charge the battery, OLED display current battery level (0%, 20%, 50%, 80%, and 100%) and the Remaining Charging Time to get the battery fully charge. The Remaining Charging Time will be shown in every10 minutes. And the display will remain lit while charging.

9. Firmware update and customizing:

Can be updated and customized through a simple software that can be downloaded directly from our website. The software will be made to run on Windows systems and will be available in English. It will also include a “help”sections for urgent questions. The directions on how to use our software will be found on our website and Facebook page.

10. Adjustment of airflow:

The bottom airflow system can be adjusted with slight twisting of the airflow ring.

11. Filling E-liquid:

The Slide-n-Fill design only asks you to slide the top lip counter clockwise to the fullest extend. Fill in juice through the opening and slide the top back.

12. Changing Atomizer:

Remove the base and unscrew the GT Cores and insert the new GT cores onto the base. Secure the base back in place. There are a variety of GT cores available for NRG Tank series. Please select the GT Cores you desire.

How to Set the Mode

1) Smart VW mode:

As an advanced Variable Wattage mode, there are 3 levels of VW: H stands for High; N stands for Normal; S stands for Soft. The default setting is Normal. VW(H/N/S) will guarantee your mod’ s ability to skillfully select the adequate average wattage for your atomizer, according to its resistance reading, automatically.

2) In CCW mode:

While on VW mode, press the mode button three times consecutively to select CCW. Select and hold down the mode button to confirm and to implement any modifications to the wattage line using the plus and minus buttons (Ramp up time and consequent performance); move on to the next bar with a quick press of the mode button. When all modifications are final hold pressed the mode button to save and exit.

3) In TC-Ni/TC-Ti/TC-SS/TCR(M1, M2) Mode:

When set in TC-Ni/TC-Ti/TC-SS mode, the device can separately support Nickel 200, Titanium, and 316 Stainless Steel coils. The OMNI Board 2.0 allows you to change the start up wattage under temperate control mode. The default wattage is 65W. You could also adjust the value of the coil within the given range. In TCR (Temperature Coefficient of Resistance) mode, the device can support different temperature control coils within different TCR value ranges and you can set the TCR at different values within proper range.

The Setting of TCR Mode (M1,M2):

When set in TC-Ni/TC-Ti/TC-SS mode ,and the device is powered on, you will enter into the TCR (M1,M2) set menu, by clicking mode bottom 3times:

Press mode button to choose among M1, M2 ;

Press the up or down button to increase or decrease the TCR value according to the material of the coil you used;

Following are different TCR value ranges for different coils for your reference:

Note:

1.The TCR value in the sheet is 10 multiplied of the actual TCR.

Our total range of TCR value is 1-1000.

Adjust temperature:

In TC-Ni/TC-Ti/TC-SS/TCR(M1,M2) mode, temperature can be adjusted from 100-315℃ or 200-600℉ by pressing up button or down button, up button to increase and down button to decrease. Each press of the up or down button will increase or decrease the temperature setting by 5℃ or 10℉. Long press up button or down button can rapidly increase or decrease temperature setting.

Lock/Unlock resistance:

In TC-Ni/TC-Ti/TC-SS/TCR(M1, M2) Mode, press the “-“and mode button simultaneously for 2s will lock/unlock the resistance level, “ ” will appear on the display. Attach a new atomizer will not change the locked resistance.

Automatic atomizer recognition:

To achieve better temperature control effect, the mod will ask the user if the new atomizer is attached. ” OLD LOAD: -, NEW LOAD: + ” will appear on the display. If a new atomizer is attached, press ” + “, the mod will read new resistance; if not, press ” – “, the mod will read at locked resistance.

4) In CCT mode:

While on any TC mode, press the mode button three times consecutively to select CCT. Select and hold down the mode button to confirm and to implement any modifications to the temperature line using the plus and minus buttons (Ramp up time and consequent performance); move on to the next bar with a quick press of the mode button. When all modifications are final hold pressed the mode button to save and exit.

5) In Bypass mode:

Direct output voltage system is applied in Bypass mode. The higher the batterylevel is, the higher the output voltage is. When set in this mode, the device can support a coil whose resistance is within the range of 0.05-5ohm.

6) Smart ON/OFF:

As an advanced Variable Wattage mode, Smart VW could be switched on and off on the main manual and it does not impact the VW(H/N/S). Enter Smart ON/OFF and press Yes or NO to confirm.

7) Screen Timeout:

The default timeout setting is 10 seconds of main manual and then switch to Real Time Clock for another 15 minutes. The timeout setting could be adjusted from 3 seconds up to 60 minutes. Enter the Screen Timeout and adjust the time up or down as you wish. For example, if you choose 3 seconds, after 10 seconds of showing the main manual, the display will be showing 3 seconds of Real Time Clock.

8). Default:

You could reset to default setting by entering Default and pressing YES.

Warning: When inserting the batteries into the new mod, remember to make sure they are new, and that they are one of a pair. Unevenly charged batteries, used batteries, or non-matching batteries may cause significant delays in charging and affect the performance of the device.

We will be happy to hear your thoughts

Leave a reply